Friday, February 27, 2015
Coil Pot Progress (February 27, 2015)
I spent some time cleaning up my pot. I started with the lower layers and removed excess bits of clay that made the pot look messy using the needle tool, the ribbon tool, and a metal knife. I worked my way upward. It was difficult to clean the inside of the pot up because there were small openings. I cleaned most of the outside out and set it out to reach the bone-dry stage before firing it in the kiln. Everytime after I work I would clean up my work area because long exposure to clay dust can be bad for your health (ceramics golden rule).
Monday, February 9, 2015
Coil Pot Process (February 9, 2015)
From where I left off, I had three layers. I added two more layers on. The fourth layer was a simple coil. I rolled it out by hand. However, I accidentally applied too much pressure, and it ended up being a little flat. But, I liked the flat texture of the coil. So I flattened the coil a little more, scored it and the base, and applied slip to it and the base, and stuck it on. After that, I made a layer of balls. Originally, I decided that I was going to make the balls the same height and size, but in the end, I changed the design and made balls that gradually increased in size and decreased in size. I did that for the entire layer, so it ended up kind of like "waves".
After that, during today's class, I used the new extruder (yay!) to create coils. I used a template that extruded three smaller coils that were stuck together. Difficult to describe. And sorry, I'll put pictures on here later. That coil turned out a little bad. It had air holes in it, so some parts were not usable. Next time, I should wedge it before putting it in the extruder. Anyways, because of the "waviness" of the balls, there are going to be gaps in between the balls and the coil. So, I used a thin coil to fill in the gaps. I scored and slipped that onto the balls. After that, I scored and slipped the "3-in-1" coil on top of the balls and the thin coils, making that the 6th layer, I think.
I really need to smooth out my pot. There are many bits of clay that make the pot look messy.
Tuesday, February 3, 2015
Coil Pot Process (February 3, 2015)
Okay, so for the past few classes, I have been working on a coil pot. First, I had to create a base. I used a rolled up slab of clay. After that, I used a plastic bowl and used a needle tool to trace around it. Then, I started to roll out my coils. I'm a fussy person that likes my coils to be smooth, so I would spend quite some time rolling them out. And if I see cracks in it, I try to patch it up as soon as possible. Anyways, over the span of two classes, I rolled out 2 coils, attached them, and used the extruder to also "squeeze" out a really long coil. Well how do you attach coils onto the base or onto other coils? It's not very difficult. First, you have to cut out the desired length of your coil. Then, using either a needle tool or fork (I prefer the needle tool), mark up (score) both the base/coil and the coil you want to put on. That way, the clay can stick together better. Then, use some slip and spread it along the marked up areas. Place the coils together, and smooth the inside part of the pot to make it more sturdy. That's pretty much it. With the coil from the extruder, I looped it. I plan on putting balls of clay in the holes. Sadly, the extruder is broken (again), and I was back to rolling out my own coils. Fortunately, I was able to get one coil out of it. The next class, when I took my pot out of the bag, I noticed cracks along the pot. I think the cracks formed because of the moisture. The base is not sturdy enough, so when I carried it , I may have pushed the base upward, causing the crack. Anyways, I rolled out two thinner coils and twisted them together to form a braid-like thing. I wanted to make a braid out of three coils, but it was difficult to get the coils thin, as I am not very experienced with clay. Two coils turned out okay, but there were cracks along the areas that I bent. I'm pretty sure that my hands dried the clay out as I rolled it. So, I "patched" the holes up with wet clay. Sorry, I don't have a picture of that yet. I scored and slipped that onto the coil. So right now, I have 3 layers. I plan on making 5 more layers. The number of layers depends on the speed I will work at and the time I have.
Subscribe to:
Posts (Atom)